ilo ssh commands

HP iLo command line interface use so called SMASH CLP command language.
...
Connecting to HP iLO via SSH.

1. How do I access iLO via SSH?
2. How do I access HP iLO console?
3. How do I connect PuTTy to iLO?
4. How do I check my iLO status?
5. How do I connect to ILO server?
6. How do I use HP ILO?
7. How do I find iLO IP address?
8. What port does iLO use?
9. What is the default iLO IP address?
10. What does iLO Reset do?
11. How do I turn on my iLO 4 server?
12. How do you paste into the iLO remote console?

How do I access iLO via SSH?

Access to HP ILO remote console via SSH

1. Open a ssh connection to the ILO's IP address. # ssh ilo_admin@ip_address.
2. Enter your ILO admin account and password. After that you will see the ILO prompt. ...
3. To access the remote console of the server at the ILO prompt type “TEXTCONS” hpILO->TEXTCONS.
4. You will be presented with the Login: console.

How do I access HP iLO console?

Tutorial HP iLO – Remote console access

1. On the prompt screen, enter the administrative login information. Factory default access information: ...
2. After a successful login, the administrative menu will be displayed. ...
3. On the Information screen, you will be offered the . ...
4. The remote console will open in a new screen.
5. You can now use the remote console as you wish.

How do I connect PuTTy to iLO?

Access the iLO Administration menu and select the Security option. On the Access Settings tab, enable the SSH service and click on the Apply button. SSH is now enabled on your HP iLO interface. Use a software like Putty to remotely connect to the iDrac interface using the Administrator account.

How do I check my iLO status?

you can go into System Management Homepage-> Management processor link, then when you click it on the left from the task pane you must be forwarded to a link for iLO and you can see the IP address.

How do I connect to ILO server?

1. Start the Remote Console application by typing the IP address of the ILOM service processor into a browser on the remote system. ...
2. Click Yes. ...
3. Enter the user name and password, and click Log In. ...
4. Click the Remote Control tab in the ILOM web interface. ...
5. Set the mouse mode to Absolute mode in the Mouse Mode Settings tab.

How do I use HP ILO?

To install the license, log into the iLo and go to the Administration page and select Licenses. Enter your product key in the provided boxes and Save. You can now use the remote console. Select the "Remote Console" Tab at the top and click on "Integrated remote console" to start your session.

How do I find iLO IP address?

During the HP server boot process, press the F9 key to access the system utilities.

1. Select the System Configuration option.
2. On the next screen, select the iLo Configuration Utility.
3. Select the Network Options entry.
4. On this screen, you will be find out the HP iLo interface IP address.

What port does iLO use?

Remote Console Port - The default value is 17990. Web Server Non-SSL Port (HTTP) - The default value is 80. Web Server SSL Port (HTTPS) - The default value is 443.

What is the default iLO IP address?

The server is pre-configured with a default, static IP address to access iLO (192.168. 0.120). The iLO default user name and password are found on the label attached to the top of the chassis.

What does iLO Reset do?

Rebooting (Resetting) iLO

Using the Reset option does not make any configuration changes, but ends all active connections to the iLO firmware. If a firmware file upload is in progress, it is terminated. If a firmware flash is in progress, user cannot reset iLO until the process is finished.

How do I turn on my iLO 4 server?

To power down the server, use one of the following methods:

1. Press and release the Power On/Standby button. ...
2. Press and hold the Power On/Standby button for more than 4 seconds to force the server to enter standby mode. ...
3. Use a virtual power button selection through HP iLO.

How do you paste into the iLO remote console?

Open that file from within the remote session (notepad, nano, grep) to get it on the screen of the remote host. Then copy and paste the lines you want with the clipboard of the remote host to a prompt or other window. There's no ability to copy/paste over an ILO console connection.