CCNA Labs HSRP Configuration on GNS3 and Packet Tracer

1. Does Packet Tracer support HSRP?
2. How do I find my HSRP configuration?
3. How do I configure HSRP?
4. What is HSRP CCNA?
5. How do I check my HSRP status?
6. How do I check my HSRP failover?
7. What is the default HSRP priority?
8. Can 2 HSRP routers become active active?
9. How do I configure Glbp?
10. What layer is HSRP?
11. What is difference between HSRP and VRRP?
12. What is the difference between HSRP version 1 and 2?

Does Packet Tracer support HSRP?

By default, Packet Tracer supports HSRP version 2. BR_R1 will be configured as the Active HSRP default-gateway and BR_R2 will be configured as Standby. Preemption is configured on both routers.

How do I find my HSRP configuration?

Use the show hsrp command to display information about HSRP groups. The brief keyword displays a single line of information about each virtual gateway or virtual forwarder.

How do I configure HSRP?

To achieve basic HSRP configuration, you need to do the following:

1. Configure normal IP address on interface (cannot be the same as HSRP virtual IP)
2. Bring interface up (no shutdown)
3. Configure HSRP group and virtual IP address using the standby command.

What is HSRP CCNA?

Hot Standby Router Protocol (HSRP) is a CISCO proprietary protocol, which provides redundancy for a local subnet. In HSRP, two or more routers gives an illusion of a virtual router. HSRP allows you to configure two or more routers as standby routers and only a single router as active router at a time.

How do I check my HSRP status?

Check HSRP UP Status

1. First visit official website.
2. On the homepage click at reschedule your appointment option.
3. After that a new page displayed on your screen.
4. Enter the following details –

How do I check my HSRP failover?

You can use the show standby command when in Privileged Mode to check the status of HSRP. This command tells you which router is active and which is standby, as well as a number of other statistics. On the PC, the default IP address should point to 10.1.

What is the default HSRP priority?

By default, the priority is 100 but the highest priority value becomes the active router for the HSRP group.

Can 2 HSRP routers become active active?

First of all, if two routers sharing the same LAN/VLAN both become HSRP Active then it means they are either not able to see each other's HSRP Hello packets (which means that clients/laptops probably can't reach one-or-both of them either) or they have mismatched HSRP Authentication keys.

How do I configure Glbp?

Enable GLBP authentication using the configured key chain and group number of 1. Change the default GLBP load balancing behavior to using weighting. Exit into global configuration mode. Create a tracked object that will monitor the line protocol status of the fa0/0 interface using an object number of 1.

What layer is HSRP?

HSRP is an application layer protocol. HSRP version 1 uses UDP port number 1985 and multicast address 224.0. 0.2 and version 2 uses UDP port 1985 and 224.0.

What is difference between HSRP and VRRP?

The primary difference between HSRP versus VRRP would be that HSRP is proprietary to Cisco and can only be used on Cisco devices. VRRP is a standards based protocol and is vendor independent allow some flexibility when choosing network devices.

What is the difference between HSRP version 1 and 2?

Version 1 is the default version of HSRP. HSRP version 2 uses the new IP multicast address 224.0. 0.102 to send hello packets instead of the multicast address of 224.0. ... HSRP version 2 permits an expanded group number range, 0 to 4095, and consequently uses a new MAC address range 0000.0C9F.